Porcelain Veneer

One of the most popular applications in dentistry is porcelain veneers and aesthetically, the satisfaction rate from porcelain veneers is quite high. This material, in the form of a thin shell placed on the teeth to cover cosmetic defects in the tooth, can be very long-lasting for the correct patient and mouth structure. In cases where oral care is not sufficient; Infection can cause problems around natural teeth, as well as problems with dentures. This directly affects the duration of treatment. As with all treatments, planning is critical so a detailed analysis is essential for the sustainability of an appropriate regimen. Different types of porcelain tooth veneers can be made. Usually, the first to come to mind is the old generation metal coatings. However, there are zirconium supported porcelain veneers and full ceramic veneers that give much better results aesthetically. With a detailed study, you will get detailed information about the tooth coating process.

How is Porcelain Dental Veneer Made?

At the first stage, the dentist considers the patient's views. The desired result with the porcelain coating process is determined according to the needs of the patient. In some cases, if there is a problem with the jaw structure, it may not be solved with porcelain treatment alone. The dentist initiates the examination process to make the most accurate decision possible about the suitability of the teeth for occult treatment. The procedures performed in dental permits are explained to the patient. If necessary, radiological examination (x-ray) can also be done. Again, if necessary, in digital systems or verbally; The condition after the procedure is roughly seen.

Porcelain Veneer Preparation Stage

To complete the oral preparation before the tooth veneer process, the dentist creates the surface of the tooth almost as thick as the parts used in the veneer. The patient and the doctor decide together whether local anesthesia will be used to prepare the tooth surface for the coating material. The dentist takes dental models of the patient to send to the dental laboratory. In the treatment of deficiency and sensitivity problems, a "temporary tooth" is made. These coatings, which do not give as aesthetic results as permanent ones, are temporary and are discarded when the day comes. Temporary teeth that are measured are delivered to the patient on the same day. The finish of permanent veneers may vary depending on the number of teeth and the practical situation. The process takes about 3-10 days. During the rehearsal phase, the patient observes the relationship of the teeth with the lip and surrounding tissues, and arrangements are made according to his ideas.

Pasting

Before the veneer is permanently attached to the tooth, the dentist will rehearse the teeth to determine the shape and color of the mold. After the technical and aesthetic suitability of the prepared tooth is ensured, the final stage is passed. It repeatedly cuts and shapes the coating for optimum results. The color of the coating can be changed according to the tooth by controlling it during the process. Then the tooth is cleaned and foreign bodies are removed before the veneer is permanently bonded. Roughening the tooth surface during scraping is essential for optimum adhesion. A special adhesive used for porcelain veneers is applied and a piece of veneer is placed on the tooth. A special beam device that activates the molecules in the chemical structure of the adhesive bonds the tooth with the veneer piece that fits correctly. In the final stage, excess adhesive is cleaned, Bite rehearsal is done and adjustments are made if necessary. The dentist may give the patient a follow-up appointment in a few weeks to see how the coatings in the mouth affect the gums. During this time, teeth can be temporarily attached to the tooth.

Porcelain Veneer Life

After your teeth are covered with porcelain, their lifespan can be extended with personalized oral care and regular dental check-ups. The intraoral structure is variable and the treatments used remain constant. It will probably need to be replaced after some time. However, if the maintenance of the coatings is done carefully and in a planned way, their useful life can reach 10-15 years. Changes may not be required for every patient. There are also patients who do not need a porcelain veneer after insertion. However, porcelain dental materials cannot be reused. A series of cuts must be made on natural teeth to make room for enamel in the mouth. After these procedures, it is always necessary to cover the teeth.

Frequently Asked Questions

How does porcelain veneer toothache go away?

Veneer solutions to improve the appearance of teeth are also aesthetic solutions. In some cases, the deformation of the tooth is due to the veneer solution. Rottens and scratches on fallen, cracked, broken surfaces can be removed with the applications we call resurfacing. However, many patients have veneers to make the teeth look more beautiful. As with all dental applications, pain may occur in certain areas after the veneer is placed. We should note that the pain is normal for a few days for our patients who wonder how the veneered toothache goes away.

What is a porcelain tooth?

The question of what is a porcelain tooth is an application that plays an important role in eliminating the problems caused by the loss of teeth or the emergence of various problems. The main purpose of this application is to eliminate gingival disorders, to give an aesthetic appearance and to improve speaking ability. This treatment is for anyone over the age of 18. It is also known that this practice has become quite common lately. The decrease in the prices of porcelain applications is also effective in the development of this situation. In addition, technological innovations in the field of health also increase the demand for this application. Because in this way, more qualified applications are made.

What are the benefits of porcelain teeth application?

Thanks to the porcelain laboratory devices developed in recent years, ceramic substructures are produced from pressed porcelain tooth material. These porcelains, which are called transparent, have achieved the same light transmittance and naturalness as natural tooth enamel, since no metal is used to provide strength. By providing full color harmony in empress or zirconium oxide applications, a thinner appearance and a perfect natural appearance have been the answer to aesthetic expectations. Empress applications have very good tissue compatibility, do not cause allergies and have good gingival compatibility. It should not be forgotten that the harmony of aesthetics, teeth and gums is possible when combined with function.